JapanCertは頼りが強い上にサービスもよくて、もし試験に失敗したら全額で返金いたしてまた一年の無料なアップデートいたします。
IT業界の中でたくさんの野心的な専門家がいって、IT業界の中でより一層頂上まで一歩更に近く立ちたくてHPのHP0-P10試験に参加して認可を得たくて、HP のHP0-P10試験が難度の高いので合格率も比較的低いです。HPのHP0-P10試験を申し込むのは賢明な選択で今のは競争の激しいIT業界では、絶えず自分を高めるべきです。しかし多くの選択肢があるので君はきっと悩んでいましょう。
JapanCertを利用するのは君の合格率を１００％保証いたします。JapanCertは多種なIT認証試験を受ける方を正確な資料を提供者でございます。弊社の無料なサンプルを遠慮なくダウンロードしてください。
最近、HPの認定試験はますます人気があるようになっています。それと同時に、HPの認証資格ももっと重要になっています。IT業界では広く認可されている試験として、HP0-P10認定試験はHPの中の最も重要な試験の一つです。この試験の認証資格を取ったら、あなたは多くの利益を得ることができます。あなたもこの試験を受ける予定があれば、JapanCertのHP0-P10問題集は試験に準備するときに欠くことができないツールです。この問題集はHP0-P10認定試験に関連する最も優秀な参考書ですから。
もし君がHPのHP0-P10に参加すれば、良い学習のツルを選ぶすべきです。HPのHP0-P10認定試験はIT業界の中でとても重要な認証試験で、合格するために良い訓練方法で準備をしなければなりません。。
君はまずネットで無料なHPのHP0-P10試験問題をダウンロードしてから 弊社の品質を確信してから、購入してください。JapanCertは提供した商品は君の成功を全力で助けさしたげます。
試験番号：HP0-P10問題集
試験科目：HP 「HP Integrity Server Multi-OS Installation and Deployment」
最近更新時間：2013-11-11
問題と解答：147
購入前にお試し,私たちの試験の質問と回答のいずれかの無料サンプルをダウンロード：http://www.japancert.com/HP0-P10.html
NO.1 You replaced failed hardware in an HP Integrity server. Which steps should you perform to ensure
that the system is operational?
A. Verify that the replaced hardware is visible in the EFI Shell, and that the Diagnostic LEDs are clear.
B. Verify that the replaced hardware is visible in the EFI Shell and that the correct firmware version is
loaded.
C. From the EFI Shell, boot the system. From within the operating system, confirm that the replaced
hardware is functioning and verify the correct status of the Diagnostic LEDs.
D. Verify that the replaced hardware is visible in the EFI Shell and that the correct firmware version is
loaded. Then boot the system and confirm that the replaced hardware is functioning.
Answer: D
HP HP0-P10 HP0-P10 HP0-P10
NO.2 You just installed an Integrity rx2620 server. How do you set the MP and system times?
A. Use the MP date command to set time and date.
B. The time will be set automatically during system boot.
C. Use the EFI shell command time to set time and date of the MP.
D. Use the MP date command to set the date, and use the MP time command to set the time.
Answer: C
HP HP0-P10認定証 HP0-P10認定証 HP0-P10 HP0-P10 HP0-P10
NO.3 You are managing an Integrity rx2620 server that is located in a remote office. Which Management
Processor (MP) console command do you use to gather the state of the system and LEDs?
A. LED
B. VFP
C. ERRDUMP D. SYSSTAT
Answer: B
HP過去問 HP0-P10問題集 HP0-P10 HP0-P10参考書
NO.4 Which Management Processor (MP) command displays the physical location information of the
system?
A. SI
B. ID
C. LOC
D. SO
Answer: B
HP HP0-P10 HP0-P10認定証 HP0-P10 HP0-P10認定試験
NO.5 You have run an Offline Diagnostics Environment (ODE) utility. What should you do before booting
the operating system or running any non-ODE utility?
A. Reset the system at the MP:CM> prompt.
B. Use the MP:CM> poff command to power off the DC voltage.
C. Reset the system at the EFI shell prompt and disconnect the AC power for one minute.
D. Reset the system at the EFI shell prompt, use the MP:CM> pc command to power off DC voltage, and
disconnect the AC power for one minute.
Answer: A
HP過去問 HP0-P10問題集 HP0-P10 HP0-P10 HP0-P10認証試験
NO.6 What does an amber blinking System LED on an Integrity rx2620 indicate?
A. System is in error state
B. Remote access is enabled
C. A system warning
D. Management Processor is powered off
Answer: C
HP参考書 HP0-P10認定資格 HP0-P10
NO.7 Which capability does the Management Processor (MP) in the Integrity rx2620 server provide?
A. offline hardware monitoring
B. hardware administration and management
C. remote HP-UX operating system installation
D. remote monitoring of server room conditions
Answer: B
HP HP0-P10 HP0-P10認定証
NO.8 You want to load new firmware for the Management Processor (MP). Which command do you use to
verify a proper connection to an FTP server?
A. xd
B. bin
C. scp
D. xu
Answer: A
HP HP0-P10認定試験 HP0-P10参考書 HP0-P10 HP0-P10問題集 HP0-P10練習問題
NO.9 You need to perform a maintenance task on a Management Processor module. Which command
displays a list of connected users?
A. who
B. list
C. usmgr
D. show user
Answer: A
HP HP0-P10練習問題 HP0-P10認証試験 HP0-P10 HP0-P10認定証
NO.10 From the EFI Boot Manager, how can you get information about the installed memory DIMMs?
A. Go to the EFI Shell and enter: info mem
B. It is not possible to get the information offline.
C. The information displays automatically at the EFI Boot Manager menu.
D. Go to the System Configuration menu and choose Memory Configuration.
Answer: A
HP HP0-P10 HP0-P10認定資格 HP0-P10過去問 HP0-P10
NO.11 The diagnostic panel on an Integrity rx4640 shows a fan failure. What information on the Management
Processor (MP) shows you when the fan failed?
A. MP:CM> PS
B. MP:CM> SS
C. MP> SL --> L - Live Events
D. MP> SL --> E - System Event
Answer: D
HP認定試験 HP0-P10 HP0-P10
NO.12 In a Linux environment, what is one of the components used to manage highly available solutions
offered by Virtual Server Environment (VSE)?
A. HP Workload Manager
B. HP OpenView Node Manager
C. HP Global Workload Manager
D. Performance Management Pack
Answer: C
HP過去問 HP0-P10 HP0-P10 HP0-P10
NO.13 Which Offline Diagnostics Environment (ODE) utility should you use to test processors on an Integrity
server?
A. WDIAG
B. IA64DIAG
C. CPUDIAG
D. PROCDIAG
Answer: C
HP HP0-P10参考書 HP0-P10練習問題 HP0-P10問題集
NO.14 Which methods of accessing the Offline Diagnostics Environment (ODE) utilities does HP recommend?
(Select two.)
A. from the HP service partition
B. from the EFI Boot Menu
C. from the MP command menu
D. from the operating system disk
E. from the Offline Diagnostic Utility CD
Answer: AE
HP参考書 HP0-P10認証試験 HP0-P10
NO.15 The system is not responding normally. You have access to the Management Processor (MP). Which
command do you use to cycle the power?
A. ps
B. pc
C. rs
D. co
Answer: B
HP HP0-P10認定資格 HP0-P10 HP0-P10認定証 HP0-P10問題集
NO.16 Where is the diagnostic panel on an Integrity rx4640 server located?
A. top
B. front
C. back
D. left side
E. right side
Answer: A
HP認定試験 HP0-P10認証試験 HP0-P10過去問 HP0-P10問題集
NO.17 You have limited access to the Management Processor (MP), but you have full access to the system
Baseboard Management Console (BMC). Which command do you issue in the BMC Command Line
Interface (CLI) to power off the system hardware?
A. cli> p 0
B. cli> rs 1
C. cli> pc 0
D. cli> loc 0
Answer: A
HP問題集 HP0-P10参考書 HP0-P10 HP0-P10認定試験
NO.18 How can you determine the firmware version that is running on an HP Integrity system? (Select two.)
A. At the EFI Boot Manager menu, open the EFI shell and enter info fw.
B. At the MP main menu, open the Command Menu (cm) and enter firmware.
C. At the EFI Boot Manager menu, go to the Firmware menu and select Version.
D. At the EFI Boot Manager menu, go to the Firmware Configuration menu and select Version.
E. If you access the EFI Boot Manager menu using iLO, the firmware versions display automatically.
Answer: AE
HP認定証 HP0-P10練習問題 HP0-P10認定証
NO.19 The rx3600 and rx6600 have LEDs which show the FRU Health status. How can you view the state of
these LEDs remotely?
A. From the MP main menu, select VFP
B. From the MP main menu, select SL
C. From the MP main menu, select CM, then LS
D. From the MP main menu, select CM, then DF
Answer: A
HP認定試験 HP0-P10認定証 HP0-P10 HP0-P10 HP0-P10練習問題 HP0-P10
NO.20 How can you access the UUID on an entry-level HP Integrity server? (Select two.)
A. The UUID is written on the system information label of the server.
B. At the EFI Boot Manager menu, access the EFI Shell; then enter info sys.
C. At the Management Processor (MP) main menu, go to the Command Menu and enter id.
D. At the EFI Boot Manager menu, access the System Configuration menu and select System UUID.
E. If you access the EFI Boot Manager menu using integrated Lights-Out (iLO), the UUID displays
automatically.
Answer: AB
HP HP0-P10 HP0-P10練習問題
NO.21 Which command do you use in the EFI Shell to verify that an Integrity rx4640 server has the latest
firmware?
A. openinfo fw
B. info fw
C. ver fw
D. sysrev
Answer: B
HP参考書 HP0-P10 HP0-P10参考書 HP0-P10認定試験 HP0-P10認定資格
NO.22 After you replace a memory module on an Integrity server, how do you clear the entries in the Page
Deallocation Table (PDT)?
A. Interrupt the boot, go to the Service Menu and enter pdt clear.
B. Interrupt the boot, go to the EFI shell, and then enter pdt clear.
C. Interrupt the boot, enter the MP:CM> CL command, and choose PDT.
D. After reboot, the system automatically deletes entries in the PDT without user input.
Answer: B
HP認定証 HP0-P10問題集 HP0-P10認定資格 HP0-P10参考書 HP0-P10
NO.23 Which front panel LEDs on an Integrity rx2620 can indicate an error?
A. Locator LED and System LED
B. Power LED and Diagnostic LEDs
C. System LED and Diagnostic LEDs
D. Diagnostic LEDs and Locator LED
Answer: C
HP HP0-P10認定試験 HP0-P10認定試験
NO.24 You must back up all your Integrity server NVRAM configurations. Which backup utility is available for
download that can be used in the EFI shell?
A. bcfg
B. getmtc
C. nvrambkp
D. bcknvram
Answer: C
HP認定資格 HP0-P10認定証 HP0-P10
NO.25 What is the difference between a Machine Check Abort (MCA) and a Transfer of Control (TOC)?
A. An MCA is a software dump; a TOC is a hardware register dump.
B. An MCA is a hardware register dump; a TOC initiates a software dump.
C. An MCA dump is for Windows systems; a TOC is for HP-UX systems.
D. An MCA dump is for HP-UX systems; a TOC is for Windows systems.
Answer: B
HP HP0-P10認定資格 HP0-P10 HP0-P10 HP0-P10認証試験
NO.26 Where does HP OpenVMS store all error information?
A. /var/adm/syslog/syslog.log
B. SYS$ERRLOG:SYSTEM.LOG
C. SYS$ERRORLOG:ERRLOG.SYS
D. SYS$MANAGER:OPERATOR.LOG
Answer: C
HP過去問 HP0-P10練習問題 HP0-P10 HP0-P10認定試験 HP0-P10認定証
NO.27 Which command in the iLO 2 controls access permissions for an Integrity rx6600 server?
A. PS
B. SO
C. PC
D. SD
Answer: B
HP HP0-P10 HP0-P10
NO.28 Which Offline Diagnostics Environment (ODE) utility should you use to test an HP Tachyon XL2 Fibre
Channel card?
A. IODIAG
B. FCDIAG
C. PERFVER
D. FCFUPDATE
Answer: A
HP認定試験 HP0-P10認定資格 HP0-P10過去問 HP0-P10認証試験 HP0-P10
NO.29 An Integrity rx2620 server with Windows Server 2003 is running terminal services but has stopped
responding. Which MP command do you use to shut down gracefully and power off the server?
A. rs -g
B. pc -g
C. rs -off
D. pc -off
Answer: B
HP HP0-P10問題集 HP0-P10認定試験 HP0-P10問題集
NO.30 Which Offline Diagnostics Environment (ODE) utility should you use to test the memory of an Integrity
server?
A. MAPPER
B. SYSDIAG
C. MEMDIAG
D. DIMMDIAG
Answer: C
HP練習問題 HP0-P10 HP0-P10 HP0-P10
JapanCertは最新の1z0-457問題集と高品質の74-325問題と回答を提供します。JapanCertの000-614 VCEテストエンジンと70-480試験ガイドはあなたが一回で試験に合格するのを助けることができます。高品質の70-684 PDFトレーニング教材は、あなたがより迅速かつ簡単に試験に合格することを100％保証します。試験に合格して認証資格を取るのはそのような簡単なことです。
没有评论:
发表评论