2013年9月22日星期日

無料にCiscoの640-816認定試験を更新する

ここで無料にJapanCertが提供したCiscoの640-816試験の部分練習問題と解答をダウンロードできて、一度JapanCertを選ばれば、弊社は全力に貴方達の合格を頑張ります。貴方達の試験に合格させることができないと、すぐに全額で返金いたします。

チャンスは常に準備ができあがった者に属します。しかし、我々に属する成功の機会が来たとき、それをつかむことができましたか。Ciscoの640-816認定試験を受験するために準備をしているあなたは、JapanCertという成功できるチャンスを掴みましたか。JapanCertの640-816問題集はあなたが楽に試験に合格する保障です。この問題集は大量な時間を節約させ、効率的に試験に準備させることができます。JapanCertの練習資料を利用すれば、あなたはこの資料の特別と素晴らしさをはっきり感じることができます。この問題集は間違いなくあなたの成功への近道で、あなたが十分に640-816試験を準備させます。

ここで説明したいのはJapanCertにあるコアバリューです。全てのCiscoの640-816試験は非常に大切ですが、この情報技術が急速に発展している時代に、JapanCertはただその中の一つだけです。ではなぜほとんどの人々はJapanCertを選んだのですか。それはJapanCertが提供する問題資料は絶対あなたが試験に受かることを助けられるからです。JapanCertが提供する資料は最新のトレーニングツールが常にアップデートして認証試験の目標を変換するの結果です。JapanCert はあなたに最新の試験研究資料を提供しますから、JapanCert Ciscoの640-816問題集を持っていたら、試験に直面する自信に満ちることができ、合格しないなんて全然心配することはなく気楽に試験に受かることができます。

JapanCertのウェブサイトをクリックしたら、JapanCertに登録した人々が非常にたくさんいることに驚いたでしょう。実はこれは普通なことです。JapanCertは毎日異なる受験生に様々なトレーニング資料を提供します。彼らは当社の資料を利用してから試験に受かりました。これは当社が提供したCiscoの640-816トレーニング資料が本当に効果的なものということを証明しました。もしあなたも試験に合格したいのなら、JapanCertをミスしないでください。JapanCertはきっとあなたのニーズを満たせますから。

試験番号:640-816問題集
試験科目:Cisco 「Interconnecting Cisco Networking Devices Part 2」
最近更新時間:2013-09-21
問題と解答:222

夢を持ったら実現するために頑張ってください。「信仰は偉大な感情で、創造の力になれます。」とゴーリキーは述べました。私の夢は最高のIT専門家になることです。その夢は私にとってはるか遠いです。でも、成功へのショートカットがを見つけました。JapanCertのCiscoの640-816試験トレーニング資料を利用して気楽に試験に合格しました。それはコストパフォーマンスが非常に高い資料ですから、もしあなたも私と同じIT夢を持っていたら、JapanCertのCiscoの640-816試験トレーニング資料を利用してください。それはあなたが夢を実現することを助けられます。

購入前にお試し,私たちの試験の質問と回答のいずれかの無料サンプルをダウンロード:http://www.japancert.com/640-816.html

NO.1 The following commands are executed on interface fa0/1 of 2950Switch.
2950Switch(config-if)# switchport port-security
2950Switch(config-if)# switchport port-security mac-address sticky
2950Switch(config-if)# switchport port-security maximum 1
The Ethernet frame that is shown arrives on interface fa0/1.
What two functions will occur when this frame is received by 2950Switch? (Choose two.)
A. The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF.
B. Only host A will be allowed to transmit frames on fa0/1.
C. This frame will be discarded when it is received by 2950Switch.
D. All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1.
E. Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be
forwarded out fa0/1.
F. Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be
forwarded out fa0/1.
Answer: BD

Cisco認証試験   640-816   640-816   640-816認定証   640-816認定証

NO.2 What is the most appropriate summarization for these routes?
A. 10.0.0.0 /21
B. 10.0.0.0 /22
C. 10.0.0.0 /23
D. 10.0.0.0 /24
Answer: B

Cisco   640-816認定資格   640-816   640-816

NO.3 What are three characteristics of the OSPF routing protocol? (Choose three.)
A. It converges quickly.
B. OSPF is a classful routing protocol.
C. It uses cost to determine the best route.
D. It uses the DUAL algorithm to determine the best route.
E. OSPF routers send the complete routing table to all directly attached routers.
F. OSPF routers discover neighbors before exchanging routing information.
Answer: ACF

Cisco   640-816練習問題   640-816認定資格   640-816

NO.4 Which protocol provides a method of sharing VLAN configuration information between two Cisco
switches?
A. STP
B. VTP
C. 802.1Q
D. RSTP
Answer: B

Cisco   640-816認定証   640-816   640-816参考書

NO.5 Refer to the exhibit.
Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)
A. It ensures that data will be forwarded by RouterB.
B. It provides stability for the OSPF process on RouterB.
C. It specifies that the router ID for RouterB should be 10.0.0.1.
D. It decreases the metric for routes that are advertised from RouterB.
E. It indicates that RouterB should be elected the DR for the LAN.
Answer: BC

Cisco認定証   640-816参考書   640-816問題集   640-816認定資格

NO.6 What are two characteristics of a switch that is configured as a VTP client? (Choose two.)
A. If a switch that is configured to operate in client mode cannot access a VTP server, then the switch
reverts to transparent mode.
B. On switches that are configured to operate in client mode, VLANs can be created, deleted, or renamed
locally.
C. The local VLAN configuration is updated only when an update that has a higher configuration revision
number is received.
D. VTP advertisements are not forwarded to neighboring switches that are configured in VTP transparent
mode.
E. VTP client is the default VTP mode.
F. When switches in VTP client mode are rebooted, they send a VTP advertisement request to the VTP
servers.
Answer: CF

Cisco   640-816問題集   640-816   640-816   640-816認定資格   640-816認定証

NO.7 How should the FastEthernet0/1 ports on the 2950 model switches that are shown in the exhibit be
configured to allow connectivity between all devices?
A. The ports only need to be connected by a crossover cable.
B. SwitchX (config)# interface fastethernet 0/1
SwitchX (config-if)# switchport mode access
SwitchX (config-if)# switchport access vlan 1
C. SwitchX (config)# interface fastethernet 0/1
SwitchX (config-if)# switchport mode trunk
SwitchX (config-if)# switchport trunk vlan 1
SwitchX (config-if)# switchport trunk vlan 10
SwitchX (config-if)# switchport trunk vlan 20
D. SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode trunk
Answer: D

Cisco   640-816認定証   640-816   640-816参考書   640-816

NO.8 Which of these represents an IPv6 link-local address?
A. FE80::380e:611a:e14f:3d69
B. FE81::280f:512b:e14f:3d69
C. FEFE:0345:5f1b::e14d:3d69
D. FE08::280e:611:a:f14f:3d69
Answer: A

Cisco   640-816   640-816   640-816練習問題   640-816

NO.9 Which two of these statements regarding RSTP are correct? (Choose two.)
A. RSTP cannot operate with PVST+.
B. RSTP defines new port roles.
C. RSTP defines no new port states.
D. RSTP is a proprietary implementation of IEEE 802.1D STP.
E. RSTP is compatible with the original IEEE 802.1D STP.
Answer: BE

Cisco   640-816参考書   640-816   640-816

NO.10 A network administrator cannot establish a Telnet session with the indicated router. What is the cause of
this failure?
A. A Level 5 password is not set.
B. An ACL is blocking Telnet access.
C. The vty password is missing.
D. The console password is missing.
Answer: C

Cisco過去問   640-816   640-816   640-816練習問題

NO.11 Refer to the exhibit.
Based on the output of the R1# show ip route command and the information presented in the graphic,
which of the following is a potential routing problem?
A. the use of summarization for discontiguous networks
B. the use of CIDR with a routing protocol that does not support it
C. the use of VLSM with a routing protocol that does not support it
D. the use of the no auto-summary command with a protocol that does not support summarization
E. the use of the ip route 0.0.0.0 0.0.0.0 command with a routing protocol that does not support it
Answer: A

Cisco参考書   640-816   640-816認定証   640-816

NO.12 The network technician is planning to use the 255.255.255.224 subnet mask on the network.
Which three valid IP addresses can the technician use for the hosts? (Choose three.)
A. 172.22.243.127
B. 172.22.243.190
C. 172.22.243.191
D. 192.168.1.160
E. 10.17.64.34
F. 10.16.33.98
Answer: BEF

Cisco   640-816   640-816認定試験

NO.13 At which layer of the OSI model is RSTP used to prevent loops?
A. physical
B. data link
C. network
D. transport
Answer: B

Cisco参考書   640-816   640-816練習問題   640-816   640-816参考書   640-816

NO.14 A department decides to replace its hub with a Catalyst 2950 switch that is no longer needed by another
department. To prepare the switch for installation, the network administrator has erased the startup
configuration and reloaded the switch. However, PCs that are connected to the switch experience various
connectivity problems. What is a possible cause of the problem?
A. The VLAN database was not erased.
B. The management VLAN is disabled.
C. The running configuration should have been erased.
D. The "mode" button was not pressed when the switch was reloaded.
E. The switch was not configured with an IP address or a default gateway.
Answer: A

Cisco   640-816   640-816認定資格

NO.15 The internetwork infrastructure of company XYZ consists of a single OSPF area as shown in the
graphic.
There is concern that a lack of router resources is impeding internetwork performance. As part of
examining the router resources, the OSPF DRs need to be known. All the router OSPF priorities are at the
default and the router IDs are shown with each router.
Which routers are likely to have been elected as DR? (Choose two.)
A. Corp-1
B. Corp-2
C. Corp-3
D. Corp-4
E. Branch-1
F. Branch-2
Answer: DF

Cisco認証試験   640-816   640-816   640-816過去問

NO.16 Why has this switch not been elected the root bridge for VLAN1?
A. It has more than one interface that is connected to the root network segment.
B. It is running RSTP while the elected root bridge is running 802.1d spanning tree.
C. It has a higher MAC address than the elected root bridge.
D. It has a higher bridge ID than the elected root bridge.
Answer: D

Cisco   640-816   640-816   640-816   640-816問題集

NO.17 A network administrator needs to configure port security on a switch.
Which two statements are true? (Choose two.)
A. The network administrator can apply port security to dynamic access ports.
B. The network administrator can apply port security to EtherChannels.
C. When dynamic MAC address learning is enabled on an interface, the switch can learn new addresses,
up to the maximum defined.
D. The sticky learning feature allows the addition of dynamically learned addresses to the running
configuration.
E. The network administrator can configure static secure or sticky secure MAC addresses in the voice
VLAN.
Answer: CD

Cisco   640-816認証試験   640-816   640-816

NO.18 The network administrator has been asked to give reasons for moving from IPv4 to IPv6.
What are two valid reasons for adopting IPv6 over IPv4? (Choose two.)
A. no broadcast
B. change of source address in the IPv6 header
C. change of destination address in the IPv6 header
D. Telnet access does not require a password
E. autoconfiguration
F. NAT
Answer: AE

Cisco   640-816   640-816練習問題   640-816参考書   640-816   640-816認証試験

NO.19 Which two statements are true about interVLAN routing in the topology that is shown in the exhibit?
(Choose two.)
A. Host E and host F use the same IP gateway address.
B. Router1 and Switch2 should be connected via a crossover cable.
C. Router1 will not play a role in communications between host A and host D.
D. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.
E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
F. The FastEthernet 0/0 interface on Router1 and Switch2 trunk ports must be configured using the same
encapsulation type.
Answer: DF

Cisco認定試験   640-816過去問   640-816   640-816問題集   640-816認証試験   640-816

NO.20 An administrator is troubleshooting a problem between routers that are using different versions of RIP.
Which two commands would provide information about which version of RIP was being sent and received
on an interface? (Choose two.)
A. show ip protocols
B. show ip route rip
C. show interfaces
D. debug rip routing
E. debug ip rip
Answer: AE

Cisco認定試験   640-816   640-816練習問題   640-816   640-816

JapanCertは最新のNS0-155問題集と高品質の70-465問題と回答を提供します。JapanCertの1Z0-511 VCEテストエンジンとDC0-260試験ガイドはあなたが一回で試験に合格するのを助けることができます。高品質の000-124 PDFトレーニング教材は、あなたがより迅速かつ簡単に試験に合格することを100%保証します。試験に合格して認証資格を取るのはそのような簡単なことです。

記事のリンク:http://www.japancert.com/640-816.html

没有评论:

发表评论